TARDIS Cosplay: Skirts and Shrug and a lot of bias binding

Well hello there!

So continuing on from last time, it’s time to get sewing! I started off with the easier parts first which were the skirts.

A simple case of sewing the panels together, putting in elastic and finishing it off with a hem? Hahaha, not quite so simple.

Ok the sewing of the panels were. Piece all the panels together at the sides, matching the notches, sew them up with about 5/8″ seam allowance and press all the seams open. You end up with huge skirts.


The channel for the elastic is where it gets interesting as you have to iron down the top of the skirts by about an inch and then turn the edge under by about 3/8″. It looks easy, but unless you’re as clumsy as me, be prepared for some toasty fingertips. It can also be a bit frustrating trying to press down a tiny slither of fabric, so thank goodness for pins (but don’t use plastic-headed pins unless you want a nice melted spotty effect). Once you got this pinned in place, sew the channel in with a top stitch making sure that annoying little slither of fabric stays under. Also make sure you leave a gap where you stitch otherwise how else are you gonna get that elastic in.

About that elastic. Don’t believe what it says on the packet. I double checked the length I had with my own waist and found I would just be able to use it all for the two skirts, however further on, there is a top that requires elastic too. So double check the elastic length before you buy it. I ended up cutting this length in half and threaded it through the channel using the old safety pin trick. Then sew the ends of the elastic toghther, stick it all in and just seal the channel up with a quick stitch on the machine.

Now the title mentions a lot of bias binding. You can see how big the panel pieces are for the skirts. I’ve nothing really against bias binding, it looks neat when it’s finished. it’s a lot of sewing and pinning. I pinned the bias binding on the inside edge of the bottom of the skirt, with one side open and against the edge. When pinning the bias binding, I folded down the ends to so no rough edge was exposed. Then I stitched around in between the edge and the crease of the fold of the binding. Double check after this to make sure you’ve caught the fabric underneath, you don’t really want holes in your cosplay. The binding was folded over the edge and top stitched outside the skirt to finish them off. Two pieces down already!

So next up I worked on the shrug. Despite there being a huge hood, it’s not as difficult as it looks. Firstly the darts, which are small folds that are stitched in place in a piece of fabric. What would’ve been a good idea was to actually mark these out when I was cutting out the pattern. So I did this with tailors chalk and pins and a ruler and hey presto, darts! I pinned along the line, matching up both ends and stitched along this (it’s best to tack this in place, especially if you are new to sewing). Do this for both the blue outer fabric and the black lining and press the seams towards the centre.

I then stiched the front pieces to the shoulder and the side, pressing the seams open and again for both the blue and black versions. To connect the lining to the outer piece, I had to sew more, yes you guessed it, bias binding, this time around the armholes. Similar technique to before, just slightly more fiddly with it being an armhole.

For the hood, again make sure you mark everything on the piece when it’s still attached to the pattern… it really helps when you’ve got to work with pleats. First things first, sew the two pieces of the hood together, for both lining and outer fabrics. It doesn’t tell you to with the instructions for this pattern, but I pressed the seam open for this (as carefully as I could!) because I didn’t want the seams to stand up on my head when wearing it. Not that it’s seen but I wanted the fabric to lay flat.

With the lining on the inside and everything right way round, I then folded and tacked the pleats in. This was tricky as marks for the pleats were on the wrong side, inside the inside of the hood so to speak. And yes it was tacked as the seam would eventually have bias binding pinned to it and I didn’t want to deal with a hedgehog for a hood.

Funnily enough, the next step was to add bias binding around the front edge of the hood. I didn’t need to worry about folding the ends of the binding over this time as it would be caught inside the final application of binding for the shrug. I pinned the hood in place onto the shrug, working from the centre back to the front and everything was stitched in place and finished with a long run of bias binding. Last thing to do was remove the tacking.

So that’s half of the pieces made for the cosplay already, with a corset and a bustle left to tackle. I can see why the pattern said 9 packages of bias binding now, good job I bought a roll. Think this project is going to give me bias binding nightmares though!

Pudding xxx

P.S. is it blue and black or white and gold? (blame my phone, I have no idea how it managed to change colour when I took the picture!)


Well Hello There!

Hello, I’m new here and I want to show my cosplays!!

Welcome to my blog!! Bear with me as I’m a brand new blogger here.

First and foremost, my name is Nichola, or Nic, or Pudding. Hence the name of the site. I am a yorkshireman living in Scotland and was dubbed as the Yorkshire Pudding pretty much as soon as I said “‘ey up, fancy a cuppa?”.

So what is The Geeky Pudding all about. Well hopefully, you will join me as I take on a variety of cosplay projects. After completeing a degree in Costume Design and Construction, I want to put my skills to something I love, which is nerdy stuff.

The first cosplay project I’ll be working on is gonna be a big one. As my friends already well know, I am a massive Doctor Who fan. Like huge. You could say bigger on the inside…… yeah sorry. So my first project for this blog has to be for this show. But not only this, myself, my mum and my boyfriend, are lucky enough to be going to San Diego Comic Con this year. Yes that comic con!! Actually pretty soon. I couldn’t believe it either. So be on the lookout for a TARDIS cosplay in my upcoming posts.

Alongside this, I intend to throw other stuff in there. I like Marvel films/comics, Star Wars, Disney films, a few bits of anime/manga, a fair bit of geeky stuff really. I also like to draw and get crafty. So be on the lookout for side projects and artwork.

Hopefully you’ll enjoy this and come back for more. Otherwise I’m just talking to myself!

In the meantime, I better get sewing!

Pudding xxx